Item Type: 12V Fog Machine_x000D_Product Material: Iron_x000D_Weight: Approx. 2137g / 4. 7lb_x000D_Rated Power: DC 12V 250W_x000D_Battery: 3. 7V 1000mAh Lithium Battery (Shipped With Built In Battery)_x000D_Applicable Object: Bee_x000D_Purpose: Cleaning Equipment_x000D_Product Size: Approx. 23x15. 5x11cm / 9. 1x6. 1x4. 3in_x000D_Thermostat:_x000D_1. There is a little smoke in the first heating machine;_x000D_2. When the mite control knob turns right to 350 degrees and the green light jumps, the display temperature will rise a part of the temperature;_x000D_3. The display temperature above 300 is safe, and the minimum temperature is 280 . Test each machine;_x000D_4. If the display exceeds 400 degrees, unplug it for inspection;_x000D_Continuous spray: plug the power cord into the machine socket, and connect the other end to a 12V battery. At this time, the voltage displays the battery voltage. Then turn on the main switch, turn the temperature control right to 350 degrees, turn on the red light for the first warm-up, and use the green light for about 8-10 minutes. _x000D_Preheating use: turn the temperature control right to 350 degrees, and immediately unplug the power when the green light is on. The temperature display above 300 degrees is within the safe range, and the minimum temperature is 280 degrees. Then go to the battery to heat and spray in this way. Use near 250 ; Every time the cleaning agent is used up for cleaning, or when the machine is cold, clean it with clean water, and then wipe the medicine pot with paper. _x000D_Note for storage: special atomizer for the machine shall not be used randomly to avoid failure_x000D_Fault check:_x000D_(1) The buzzer sounds when the pump is pushed. The motor cannot turn out the liquid medicine_x000D_(2) After heating for more than 10 minutes, the red light does not go out. Check to see if the rear voltage display is too low. _x000D_(3) The voltage of the power cord is not displayed, and none of the above traffic lights is on. Check whether the power cord is powered on. _x000D_(4) Check whether the heating core is blocked without fog. _x000D_Three methods of spray:_x000D_Use it for the first time within about 1 second, and then increase the dosage slowly. The dosage of each bee farm is different. The amount of fog is increased or decreased by the number of seconds according to the swarm potential. The specific operation is as follows. _x000D_1: Nest door spray: When the weather temperature is low, the bee's nest door does not fan, and can be sprayed through the nest door. The nozzle does not need to be plugged into the nest door. It is about 1-2 cm away from the nest door and can also be sprayed in from the side without the bee nest door. (Disadvantages: The bee fan fog is blown out in the hot weather, and the efficacy drops by 30%)_x000D_2: Sand cover spray In hot weather, it is not easy for bees to fan the nest door spray. Spray from the sand cover with air circulation. The nozzle can be bent at a certain angle to facilitate spraying into the bee path. When spraying, it is operated from left to right. (Disadvantages: It is difficult to lift the lid, and the efficacy is about 20% lower than that of the nail hole spray)_x000D_3: Nail hole spray: the nail hole is sprayed to ensure that there is no propolis blockage in the nail hole. If it is a high box group, the hole can be drilled 2 cm from the relay box to the partition board. The above nail holes should face the side beam and not the bee path. According to the situation of your own bee farm, you can adapt to the circumstances. (We suggest that this method is effective with less waste) 1For Timer: Manually rotate the electronic timer for 0?3 seconds. Within one second of the first use, the drug resistance of bees will increase. Hand in one, precise control. If the front push does not release, it will stop for a fixed second, the push rod will stop immediately, and the rear pull lever will reverse, and it will not work at this time. 2Push Rod Switch: Push forward the spray, and if the residual fog on the letter is large, pull it down and let it go immediately, so as to save the environment. Back pull back oil 3High Temperature Resistant: The spray outlet is not hot at low temperature, and micron level atomization and ultra strong penetration are all pervasive. 4Rubber Foot Pad Bottom: There is a rubber foot pad at the bottom of the 12V fog machine, which can stably place the table top, and is not easy to tilt upside down and scratch the table top. 5Portable Handle Design: 12V fog machine has a portable handle, which is easy to use, providing you great using experience.