2 Channel Touch Screen Oscilloscope 110MHz Bandwidth Multifunctional Measuring Instrument AC100‑240V EU Plug Item Type: Oscilloscope Display Type: 7in TFT LCD on opposite corner Display Resolution: 800 (horizontal) x 480 (vertical) pixels Display Type: Point, vector Waveform Brightness: Adjustable Grid Type: Solid line, dotted line, none Grid Brightness: Adjustable Screen Brightness: Adjustable Afterglow: 1s, 5s, 10s, 30s, unlimited, off Standard Interface: USB Host, USB Device Power Supply: DC100-240V, 50-60Hz; DC input 5V3A, 9V2A, 12V1.5A Power Consumption: Less than 8W Fast Charging: Support fast charging Battery: 2 x 3.7V built in rechargeable lithium battery 2600mAh (built in battery) Operating Temperature: 0℃-50℃ Storage Temperature: -20℃-70℃ Humidity: ≤+104℉ (≤+40℃): Relative humidity ≤90%; 106-122℉ (+41-50℃): relative humidity ≤60% Cooling Mode: Convection Altitude: When in Operation: 3000 meter (10000 feet) Random Vibration: 0.31gRMS at 50Hz to 500Hz, 10 minutes per axial direction When Not in Operation: 2.46gRMS from 5Hz to 500Hz, 10 minutes per axial direction Oscilloscope Size: Approx. 248 x 176 x 54mm / 9.8 x 6.9 x 2.1in Horizontal Scale Range: 2ns/div-100s/div1, 2, 5 steps Incremental Time Measurement Accuracy (Full Bandwidth): ± (1 sampling interval+100ppm x Reading+0.6ns), >16 times average, ± (1 sampling interval+100ppm x Reading+0.4 ns), sampling interval=seconds per division ÷ 200 AD Converter: 8 bit resolution, simultaneous sampling for each channel Oscilloscope Vertical Scale Range: 10mV/div-10V/div at BNC input Vertical Resolution: 8 bit Vertical Sensitivity Range: 10mV/div-10V/div Offset Range: ±1V maximum (100mV/div), ±10V maximum (1V/div), ±50V maximum (10V/div) Dynamic Range: ±5div (8bit) Dynamic Range: ±5div (8bit) DC Gain Accuracy: ±3% FullScale Channel Isolation: 40dB, DC to the maximum rated bandwidth of each model Note: When using X1 probe, the bandwidth is reduced to 6MHz Sampling Rate Range: 250MSa/s Acquisition Mode: Normal, average, peak, high resolution Waveform Interpolation: (sinx)/x Single Sequence: Acquisition Mode: Acquisition stop time Normal and Peak Detection: all channels conduct single acquisition at the same time Average: All channels conduct N times of acquisition at the same time. N can be taken as 2, 4, 8, 16, 32, 64, 128, 256 Storage Depth: 8Mpts Mode: Automatic, normal, single time Level: CH1 CH2, ± 4 divisions from the center of display screen Release Inhibition range: 8ns-10s Trigger Level Accuracy: CH1 CH2 Trigger Sensitivity: ± 0.87div (2mV/div), ± 0.78div (5mV/div), ± 0.69div (10mV/div), ± 0.52div (20mV/div), ± 0.47div (50mV/div), ± 0.26div (100mV/div), ± 0.26div (200mV/div), ± 0.47div (500mV/div) ±0.26div(1V/div)，±0.26div(2V/div)，±0.26div(5V/div)，±0.26div(10V/div) Edge Trigger: Slope: Rising edge, falling edge, double edge Data Source: CH1 CH2 Pulse Width Trigger: Polarity: Positive polarity, negative polarity Conditions: <, >, !== Data Source: CH1 CH2 Pulse Width Range: 8ns-10s Video Trigger: Signal Standards: NTSC, PAL, HDTV720p, HDTV1080p, HDTV1080i Data Source: CH1-CH2 Synchronization: Scanlines, number of lines, odd field, even field, all fields Slope Trigger: Slope: Rise, fall Conditions: <, >, !== Data Source: CH1 CH2 Time Range: 8ns-10s Timeout Trigger: Data Source: CH1 CH2 Polarity: Positive polarity, negative polarity Time Range: 8ns-10s Number of Channels: 2 analog channels Input Coupling: DC, AC or ground Input Impedance: 1M Ω± 2% Input Capacitance: 18pF ± 3pF Probe Attenuation: 1X, 10X Support Probe Attenuation Coefficient: 0.01X-10000X