Simply connect the motherboard of the UPA programmer directly or using a DB9 male/female extension cable (1:1). Insert the correct configuration key into the slot on the main board and start programming via ZIF or DIP female. You can also use the included DIL to 10 flat ribbon pins, place it inside the ZIF plug, and connect a clip or clamps for the use of ISP from there. MCU. Choose the adapter you want to use, connect the flat cable for the adapter (PIN1 is always indicated on both the cable and the adapter), and also on the 10-pin ISP connector on the main board. Select the VCC supply source via the bridge on the main board next to the ISP connector (on = target UPA supply, off = target has its own supply). Slide the adapter over the soldered PLCC MCU on the target PCB. (No welding, no pinout revision, no pin counting—saves a lot of time and prevents errors, allowing your work to be faster, more accurate, and easier). Once your workshop is equipped with our set of adapters, you will have a new UPA experience.Supported devices: STMicroelectronics: ST62-40/45/49 NSC: CR16-HCS5(9)/MCS5(9)/MES5(9)/MFS5(9)/MCT5(9)/HCT5(9) PIC: PIC12F-508/509/629/675, PIC16F-627(A)/628(A)/648A/72/73/74/76/77/818/819/83/84(A)/870/871/872/873(A)/874(A)/876(A)/877(A) MC68HC05: B6/B8/B16/B32/E6/E6/H12/L28/P3/P3*/X16/X32 MC68HC08: AS20, AS32, AS60, AZ32, (9)08AZ32A, 908AZ60, 908AZ60A MC68HC11: A1/A8/E9/EA9, E20/F1/K4/KA2/KA4/KG4/KS2/KS8/L6/P2/PA8/PH8 MC68HC912: B32/BE32/D60/D60A/DC128A/DG128/DG128A MC9S12: D64/A128/DG128/DG256/H128/H256 Atmel 8051 Architecture: AT89S-51/52/53/8252/8253 Atmel AVR 8-Bit: AT90S-1200/2313/232/2333/2343/4433/4434/8515/8535, ATmega-8/16/161/162/163/323/64/103/128, ATtiny-12/15/2313 EEPROMs: 24C-01/02/04/08/16/32/64/65/128/256/512, 85C-72/82/92, BAW574252, -003/004/005, KKZ-06F, MCM2814, PCA8581, PCF85-81/82/94/98/102/116, SDA25-16/26/46, X24C-00/01, 7002, 93C-06/14/46/56/57/66/76/86, 93S-46/56/66, GRN-001, GRO-002, KKZ-01, S220, S2914, ST61907, XLS93C46 EEPROMs: M35080, 25C-010/020/040/080/128/160/256/320/640, M25P-05/10/20/40/80, ST950-10/20/40/80, ST95-160/320/640, ST95P-02/04/08, X50-43/45 CXK-1011/1012/1013, M6M800-11/21/41, SDE2506, TC89-101/102 EEPROM only: uDP780-828A/948/949/973/974TMS TMS370CX-02/32/36/42/56, 78K0/HC912 TMS370CX58, 78K0/HC912 TMS375C006 Color: red + green + blue Material: plastic + metal Package Contents: 1 x UPA programmer 1 x USB cable 1 x Mainboard with 40-pin DIL ZIF (600mil) socket and 14-pin SOIC ZIF (150mil) socket Only the above package content is included; other products are not included. Note: Lighting and different displays may cause the color of the item in the picture to differ slightly from the real thing. Measurement allows an error of +/- 1-3 cm.