1、Engine immobilizer system, which can protect your car from theft when it is parked or when it is forcibly removed from your vehicle. 2、An electronic system that recognizes the owner of the car and has the unique ability to prevent intrusion by not allowing the engine to start. 3、With the additional function of progressive cut‑off, it can ensure that your vehicle cannot be started by a simple jumper. 4、You will be able to select, during installation, from the first 1.5 minute stage or the second stage of 3 minutes for the activation of the alarm system, as well as the ability to program up to 2 transmitters for each system. 5、Provided a switch for the system, you can choose auxiliary parking and emergency shutdown. It also includes an LED indicator to show the status of your vehicle. Item Type: Engine Immobilizer System Material: ABS Color: Black Battery Type: Button battery (included) Battery Capacity: 120mAh Battery Model: CR2025LED Status LED DisplayNumber of flashesStatus Red/GreenStaggered flashing traffic lightsIndicates that the engine is on RedFlashing red lightActivate the first stage of anti-robbing RedRed light is onActivate the second stage of anti-robbing GreenGreen light on for 2-4 secondsThe remote control transmits a signal (the signal is recognized) GreenSteady green lightLearn code mode Does not light upshut downSystem shutdown Instruction: 1.This system is a device that controls the engine to stop. When your car is parked, it can protect the car from being stolen; or when you are forced to leave the car by others, it can also protect the car from being stolen. It can protect the safety of the car even when you are away from the car. 2.This system has the function of controlling the engine circuit and oil circuit, and the time for automatic flameout is 1.5 minutes or 3 minutes. Note: It is recommended to install the LED status indicator in a concealed place to prevent the on/off status of the anti-robbing device from being detected by intruders. Operation Method: 1. The remote control is turned on Press and hold the remote control button for 8 seconds until the indicator light is on, then the remote control enters the working state and the indicator light starts to flash intermittently. 2. The remote control is off Press and hold the remote control button for 8 seconds until the indicator light is off. At this time, the remote control is off and the indicator light does not flash. Only manual buttons can work. 3. Turn off the system Press the emergency release button 5 times to turn off the protection system. This operation can confirm the identity of the car owner and allow the engine to be started. Through this emergency release, the car works normally 4. Driving Recognition Before entering the car, turn on the remote control, the LED indicator light will be on for 4 seconds, indicating that the host system has recognized the signal sent by the remote control, and then the red and green lights of the LED indicator will flash alternately to confirm the signal reception and display the state of the car normally. 5. Automatic Anti-Robbing If you are driven out of the car and you have not had time to do any protection operations, this device will automatically complete it for you. At this time, the car will automatically turn off after 1 minute and 30 seconds (phase 1), or 3 minutes (phase 2). 6. Learning Code Method First, temporarily release the system. Press the emergency release button 5 times and the LED indicator turns green. Long press the emergency release button until the green light flashes quickly. Press the button of the remote control and the LED indicator flashes red and green, indicating that the remote control has learned successfully. This operation allows you to learn 2 remote controls at the same time. The code learning time for each remote control cannot exceed 2 seconds. Once the programming is successful, please turn on the system protection device. Installation Method: 1. Install the host in a concealed position in the car, away from moving parts. 2. The LED status indicator is installed in a place that is not easy to be found. 3. The emergency contact switch must also be installed in a concealed position. 4. The red/black wire is connected to port 85 of the relay, 86 is connected to the positive pole, and port 87a is connected to the original car flameout device circuit. 5. The black/white wire is connected to port 85 of the relay, 86 is connected to the positive pole, and port 87 must be connected to the oil pump circuit. 1 x Control Box 3 Bundle of Cable 2 x Remote Control 1 x Manual