Specification:Material: ABSProduct size: 98*34*10mm/3.85*1.33*0.39''Rated voltage: 12 (V)Rated current: 10 (mA)Installation mode: wireleCorresponding frequency: 315MHZ,433MHZModulation mode: ASKWirele transmiion distance: 50-100m (open space)Application: garage door, alarm, automatic door, rolling door, etcType of copied chip: 2260 (e.g. PT2260, SC2260, LX2260,HX2260); 2262, (such as PT2262, SC2262, LX2262,HS2262,HX2262, etc.), PT2264, PT2240 (LX2240), 1527(such as EV1527, HS1527, HX1527), FP527, CS5211, SMC918, SMC926, AX5026, ax5326-3, ax5326-4, HT600, HT680, HT6207, HT6010, HT6012, HT6013, HT6014, HT12D, HT46F49E, PIC16F629, PIC16F630, etc., can also copy other types of chips compatible with the above mentioned chips. Different chip manufacturers will have different prefix chip model, as long as the chip model numberPartof the same can be copiedNote: We generally do not recommend copying roll code chip, because there is a lot of uncertainty when copying roll code chip. When copying roll code chip remote control, we cannot determine whether the original remote control chip is an encryption chip or not, and we do not recommend copying roll code remote control with a pair of remote control.Operation Manual:1. Clean code: shut at the same time hold the lock with two keys (some of the shell are the two key) upward and downward, theLEDindicator lights flashing three times, pre release any one of the key, another is not loose, click the release button three times, rapid flashingLEDlight into the state, at this time of memory data all cleared, after cleaning the data of the remote control, pre any key, theLEDindicator is on.2. Copy: One hand-held original remote controller, the other hand-held copy remote controller, two remote controllers as close as poible, (ideally two remote controllers zero distance side by side on the desktop) respectively pre the required copy buttons,LEDindicator flickers quickly after three flickers, copy succe, other key operation method is the same. Some remote controllers have low transmitting power, so they should be equipped with remote controllers and back-to-back operation of copying remote controllers to cope well. If there is interference in some operating environments, interference operation should be avoided. If copying is not good, copying should be done again after code clearance.3. Recovery: When you inadvertently clear the code of the copying remote controller, you can pre the bottom two keys of the copying remote controller at the same time. After three flashes of theLEDlamp, it will flicker quickly. After release, you pre any key again and the light is long, which indicates that the code of the copying remote controller has been restored. Before using our copy remote control to copy, please make sure to clear the existing code of the copy remote control first.4. How to control some of the keys after copying, and the rest can not be controlLED, you can use the tips of cleaning and restoring operation, the specific operation is as follows:(1) Clearing the code first.(2) Copy the keys that have not been copied succefully again after the succeful code clearance, and do not copy the keys that have been copied succefully before.(3) Clearing the code again.(4) Make a restore operation once; at this time, the key that had not been succefully copied was covered by the new copy code, while the original copy of the succeful code was retained. If there are still keys that have not been copied succefully after the second copy, they can be coded again, and the keys that have not been copied succefully can be copied again, and then coded and restored again. This is repeated until all keys are succefully copied. This little trick can be used to reduce the hale of repetitive operations.Warm Tips:1. Prerequisites for selecting the duplicate remote controller: the original remote controller has normal function, the remote control chip is the same or compatible, and the remote control work frequency is the same.2. The copying remote controller can only copy fixed code, learning code chip and remote controller of some single chip computers (the type of chip that can be copied is shown in the description of the type of chip that can be copied).3. Two-way remote controller, scroll code remote controller and single-chip encryption program remote controller can not be copied. Such as HCS200, HCS201, HCS300, HCS301, etc.4. Before copying the remote controller, make sure that the existing code of the remote controller has been cleared and check whether the code has been cleared succefully. Otherwise, replication is not poible.5. Make sure your remote controller has enough power when copying. The closer the two remote controllers are, the better. If the copy distance is too close, the switch can copy from different angles. Preing the button of the original remote control requires that the transmitting signal be completely normal, and then pre the button of the duplicate remote control to ensur